10 Best Cnc Router Spindle of February 2026

• 【2.2KW 220V Water Cooled Spindle Motor ER20 Collet】Notice: (1) The spindle speed can't lower than 9000rpm!!!! (2) This spindle only supports clockwise rotation, not reverse rotation.
• (3) Runout off: less than 0.02mm; Accuracy: 0.003--0.005mm; Speed:0-24000rpm; Frequency: 0-400Hz. (4) This Spindle motor kit applied to Lathes, Mills, Car Hoists, Pumps and Conveyors, etc.
• 【2.2KW 220V VFD CNC Spindle Motor Inverter】Input Voltage: 220V(+/-15%); Output Voltage:208-240VAC; Input Frequency: 48-63 Hz; Output Frequency: 0-400 Hz; Input Phase: 1phase; Output Phase: 3 phase
• 【75W Water Pump with 5M Pipe】Pump length:3.2m; Voltage:220-240VAC; Flow:3000L/H; Size:150x80x140mm
• 【14pcs/set ER20 Collets】Size: 3.175mm,1mm, 2mm, 3mm, 4mm, 5mm, 6mm, 7mm, 8mm, 9mm, 10mm, 11mm, 12mm, 13mm.

RATTMMOTOR

• Model: 2.2KW Water Cooled Spindle&VFD&Clamp&Pump&Pipe&Collet CNC Kit
• Operating Speed:0-24000rpm;Frequency:400Hz;Voltage:110V;Runout off: less than 0.005mm
• Bearings:4pcs bearings;Lubrication:Grease;Current:8.5A;Size:80x200mm
• 2.2KW Inverter VFD 110V (110V input and 110V output)
• 14Pcs ER20 Collet (include 1mm, 2mm, 3mm, 3.175mm, 4mm, 5mm, 6mm, 7mm,8mm,9mm,10mm,11mm,12mm,13mm)

CNCTOPBAOS

• DC: 24V. Speed: 20000/min.
• Experience a quick and easy upgrade for your Genmitsu Desktop CNC.
• Pre-installed motor noise suppression PCB provides enhanced performance.
• It's compatible with All 3018 Series CNC router. Applied to lathes, mills, car hoists, pumps & conveyors, etc.
• Double ball bearing brush. CW/CCW rotation.

Genmitsu

• Air Cooled Spindle-- Power: 500W; Idling Speed: 2000-12000r/min; Torque：0.5NM; Diameter: 52mm.
• Speed Controller: Input Voltage: AC100-AC220V±10% Global voltage 50/60Hz; Current Limit: 6A; Wiring: Terminal type (Convenient and fast).
• Adopt pulse width technology to make the speed more stable, and the speed is high under low speed.
• With overcurrent protection cut-off device to make performance more reliable; With a soft start device to eliminate motor starting current is too large.
• Note: This motor has quiet operation, small volume and high speed, and the rear end of the motor is reinforced with a cooling fan, which can be safely worked for a long time!

RATTMMOTOR

• Engraving Machine Brush - The special brush for engraving machine is exquisite in appearance and excellent in workmanship.
• Thicken and Encryption - The practical workmanship for the thickness is 5mm, make it more durability and longtime used.
• Premium Quality - Good elasticity and canvas stitching for the brush, ensure the quality and not easy to break.
• Dimension - Hem height: 20mm; over height: 70mm; roll length: 1 meter.
• Application - The brush vacuum cleaner is suitable for CNC Router Spindle Motor.

Acrux7

• Notice:The spindle speed can't lower than 9000rpm!!!!
• Spindle--Power: 1.5KW; Voltage: 220VAC; Current: 8A; Frequency: 400HZ; Speed: 24000rpm; Collet size: ER11
• VFD--Input Voltage: 220V(+/-15%); Output Voltage: 208Vac-240VAC; Input Frequency: 48-63 Hz;
• VFD with perfect error protection and short circuit starting protection capability
• Main application: Wood, Aluminum, Plastic, PVC, PCB, etc. Industry

RATTMMOTOR

• Spindle Clamp for FoxAlien 4040-XE CNC router machine.
• Compatible with DWP611
• Outside Dimension: 7.9x9x6cm. Diameter: 7cm

FoxAlien

SZCY LLC

• 【CNC Spindle kit 500W】- 1 x 500W Air-Cooled Spindle Motor, 1 x AC110V/220V Speed Governor with MACH3, 1 x 52mm Mount bracket, 13 x ER11 collect, 4 x Screws(free).
• 【500W CNC Spindle motor】- Operating voltage: 100VDC, Power: 500W, Input: AC110V, Speed: Up to idle up to 12,000 rev / min, Torque: 5000G/CM. Insulation resistance:> 2 megohms, Dielectric strength: 400V. Motor Length: 200MM, High precision spindle run out 0.01-0.03.
• 【Speed Power Switch】- Input voltage: AC110V/220V, 50/60Hz. Output current peak: 6A. Output voltage: DC0-100V. Please install in the place that is draughty, no dramatic impact, no vibration, no explosion hazard medium, no conductive metal particle.
• 【 52mm Mount Bracket】- Made of high quality cast aluminum, this spindle motor bracket clamp is strong and durable. Diameter: 52mm, Chuck portion length: 45MM, Chuck portion diameter: 16mm.
• 【ER11 Collet Chuck】- 13Pcs ER11 Collet Set Gripping Range: 1MM to 7MM(1mm,1.5mm,2mm,2.5mm,3mm,3.5mm,4mm,4.5mm,5mm,5.5mm,6mm,6.5mm,7mm). Run-out tolerance 0.01mm. For CNC milling Lathe Tool & Work holding Engraving machine.

MYSWEETY

• Type: CNC Dust Cover Brush.
• Hem height: 20mm; overall height: 70mm
• Roll length: 1 meter
• For CNC Router Spindle Motor.
• Engraving Machine Brush.

Konmison