10 Best Table Saw Accessories of December 2025

• This 5 piece safety kit is designed to be your essential safety protection to help from getting to close to the cutters or blades on a router table, shaper, band saw, table saw and jointer. From the narrow v-style push stick, to the beefy long push block, this kit has all the bases covered in regards to many different woodworking applications.
• Each device in this kit is intentionally made in the SAFETY ORANGE color for high visibility when in use. This provides the user the ability to see exactly there hands are at during the cutting or milling process. Being SAFETY ORANGE also allows for you to easily find the device when its not in its normal location.
• The general idea behind these safety devices is to help you guide and control your stock when feeding through a table saw, band saw, jointer or a router table. The push blocks are generally used on jointers and some router applications, while the push sticks are primarily used on table saw projects. All five devices help prevent kickback and protect your fingers and hands during your cutting process
• Soft, receptive, rubber foam pads line the bases of the two small push blocks and the large push block. The rubber soles make pushing and controlling your stock much easier and safer then when doing it by hand. The soles are also washable with with warm water. Must let the rubber soles dry for 24 hours prior to using them again.
• The 5 piece safety kit includes 2 each small push blocks (1 angled handle and 1 offset handle small push block), 1 each long or large push block, 1 each standard width push stick and 1 narrow width safety-v push stick.

Peachtree Woodworking Supply

Design Originals

• This 4 piece safety kit is designed to be your essential safety protection to help from getting to close to the cutters or blades on a router table, shaper, band saw, table saw and jointer. From the narrow, magnetic push stick, to the versatile feather board, this kit has all the bases covered in regards to many different woodworking applications.
• The general idea behind these safety devices is to help you guide and control your stock when feeding through a table saw, band saw, jointer or a router table. The push blocks are generally used on jointers and some router applications, while the push stick is primarily used on table saw projects. The feather board can be mounted multiple ways and works on router tables, shaper tables and table saws.
• The feather board can be used on a table saw, router table or even a router fence You can secure the feather board into standard 3/4” wide by 3/8” deep miter slots using the innovative expanding miter bars. The feather board can also be secured using the supplied t-bolts. The t-bolts can secure the feather board to 1/4” t-track slots like those found on some router tabletops and router table fences.
• Soft, receptive, rubber foam pads line the bases of the two push blocks. The rubber soles make pushing and controlling your stock much easier and safer then when doing it by hand. The soles are also washable with with warm water. Must let the rubber soles dry for 24 hours prior to using them again.
• The magnetic handle push stick is perfect for pushing stock through on a table saw. It works exceptionally well when used in conjunction with the feather board. The 4 Piece Woodworking Safety Kit includes: 1 each multi-mount feather board, 1 each magnetic handle push stick, 1 each straight handle push block and 1 each angled handle push block.

Fulton

• Dust Collector Bag with Wire Support Frame;
• Helps keep work area cleaner; Collects up to 75% of dust and particles;
• Replaces Bosch part TS1004; Easy to attach and detach to your tablesaw;
• Dimensions: L 31" x W 13.7" head side x W 9.8" end side, D of ring 2.5" up to 2 7/8";
• Can be used with other table saws that have 2-1/2 inch dust ports on the exterior of the saw.

• When you need to cut a narrow piece of stock on a table saw we know that it can be a little dicey or intimidating. Many of us try to cut the piece we need on the outside of the blade rather than dealing with narrow cuts. However, cutting narrow stock is sometimes unavoidable. In this case it is recommended that you use a safety device such as a push stick to help feed the stock through. Push sticks also help you safely push a workpiece, keeping it flat against a table top while it is being cut.
• Designed to keep your hands away from blades or cutter, this push stick is an essential tool for your safety. The push stick prevents your hand from getting to close to the cutters or blades on table saws, router tables, shapers and jointers. The push stick has a 90 degree notch on the end with a relief circle to accept the 90 degree corner of your stock. The notched end is designed to be at the ideal angle to the handle and allows for even pressure while pushing stock through the blade.
• One of the “handiest” features of this push stick is that we have embedded two magnets into the handle. We have done this because many of us have a hard time keeping track of our tools once we are done with them. The embedded magnets remedy this issue by allowing you to place the push stick directly on metal surfaces like the side of a table saw cabinet. We have embedded not just one, but two separate magnets on to the handle to keep the push stick from sliding or inadvertently rotating.
• The push stick end has been intentionally colored a bright “safety orange” for the simple reason of being able to see the stick at all times when in use. This ensures that you can see exactly where you are placing the push stick in relation to the blade or cutter. The bright color also makes the push stick easy to locate when it stored away.
• The Magnetic Handle Push Stick measures approximately 12” long and has an ergonomically designed handle that delivers more precise control and a comfortable grip. The push stick also has a hole drilled into the handle just in case you don’t have any metal surfaces to place the push stick. The hole allows you to hang the push stick just a like the rest of your tools . Includes 2 Safety Push Sticks.

Fulton

• The Fulton Miter Gauge is a high quality, well thought out and economical solution for your table saw cross cutting needs.The Aluminum Miter fence is equally well thought out with its 45 degree ends for unsurpassed workpiece support and its ability to mounted to most any miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw. Together these three items are the perfect compliment to each other for your table saw cutting needs.
• The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place.
• The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
• Made from a single piece of extruded aluminum, this precision miter gauge fence is not only durable, its accurate and saves setup time. The fence is designed to be used with most any miter gauge with its off-set mounting track on the back of the fence. The off-set track allows you to flip the fence for lower profile miter gauge mounts and flip back for standard height miter gauges. The fence can be mounted to older miter gauges by adding a wooden block mount with wooden screws if necessary.
• Both ends of the fence are cut at exactly 45 degrees. This allows you to position the fence extra close to the saw blade (with the power turned off) so you have even more control over the workpiece you are cutting. The fence comes with a flip stop that makes repetitive cuts a breeze. When not in use the flip stop can be flipped up and out of the way. Also include are two sticky back measuring tapes. 1 tape is left to right reading and the other is right to left reading.

Fulton

• Protect hands and prevent kickback like never before
• Powerful high-friction durable grip for extreme hold
• Precision cutting and control down to 1/4" Ripping
• Fully adjustable for easy handling
• Work with small stock safely on the table saw, Router table, Jointer, & Band saw
• Made in USA. A true MICROJIG Innovation.
• Extended 3-Year . 100% Satisfaction .
• 3-Directional Force for total control of the workpiece
• Moving-Blade-Guard Hand protection
• Precise 1/4" thin rips
• Virtually eliminates kickback
• Work with small stock safely

MICRO JIG

• This innovative feather board design provides consistent tension and maximum holding pressure created by unique split rail construction
• Pre-load tension design maintains consistent pressure across face of the feather board
• 5/8" And 3/4" Metal miter bars fit all standard miter slots
• Dual Slide Motion-side to side and forward action for quick and easy setup
• All mounting hardware included for nearly any operation 3/4 and 5/8-inch wide miter bars and T-slot bolts for applications on most standard table saws, Router tables, and fences
• Split rail miter bar construction-provides maximum hold
• Ergonomic knobs help prevent over-tightening and provides non-slip loosening
• Dual Slide Motion-side to side and forward action for quick and easy setup
• All mounting hardware included for nearly any operation 3/4 and 5/8-Inch wide miter bars and t-slot bolts for applications on most standard table saws, router tables, and fences
• Unique Pre-Load Tension Design-quickly set tension for consistent cuts while reducing the chance of kick-back
• Split rail miter bar construction-provides maximum hold
• Ergonomic knobs help prevent over-tightening and provides non-slip loosening

Milescraft

• If you own a table saw, you probably have come across a situation or two where you need to make smaller cuts or make cross cuts. You may also have had the need to make repetitive cuts of the same length. Making small cuts, cross cuts and repetitive length cuts is where table saw crosscut sleds excel. Crosscut sleds help stabilize the work piece and are very accurate since they are essentially calibrated to your saw during the sled building process.
• Some time ago we noticed a lot of companies had UHMW bars available for purchase. While we as a woodworking company know exactly what they are used for, many novice or non-woodworkers do not. That’s when we decided to create this package with pre-cut UHMW bars, pre-cut aluminum track, a knob and bolt and an easy to understand how to guide booklet so you can create your very own, custom crosscut sled to fit your table saw!
• UHMW bars are most commonly used as runners for crosscut sleds since they don’t produce as much friction as wood does. Another advantage is that UHMW won’t expand or contract like wood does during drastic weather changes. Each bar is approximately 3/4” x 3/8” which fits most standard table saw slots. UHMW bars are also slick and won’t leave any residue, dust or shavings behind like wooden bars tend to do.
• The tracks that are included in this kit are made from solid extruded aluminum and are Made in the USA. Each track is cut to length for the perfect sub-fence on the crosscut sled. The included knob and bolt is for making a simple stop block which when finished, can slide the length of either track along the sub-fence. The stop block will allow you to make repetitive cuts without having to constantly move and measure the fence distance each time you make a cut.
• We have also included a full color and detailed how to guide book to help you with the crosscut sled building process. Each kit comes with 2 each 19” long by 3/4” by 3/8” UHMW bars, 2 each 12” long mini tracks, 1 each knob, 1 each 1/4” by 20 tpi bolt and a how to build your own crosscut sled guide book. Make your crosscut sled to the size you want or need for your table saw and your specific cutting needs. Please Note, the bars do NOT FIT RYOBI table saw track slots.

Fulton

• PATENT PENDING PUSHBLOCK MAKES NARROW RIP CUTS ON THE TABLE SAW SAFER AND EASIER TO CONTROL- Make your table saw rip cuts down to a 1/4" wide smooth, easy, and safe! The Delmar Tools patent pending push block creates an adjustable width tunnel for the table saw blade to pass through under the push block on difficult narrow rip cuts as small as 1/4”. Gain complete control of both side of stock on your rip cuts.Helps reduce kickback while keeping your hands above and away from the saw blade.
• THE BEST TOOL FOR EFFECTIVELY RIPPING THIN STOCK ON THE TABLE SAW- Unlike cumbersome push sticks and feaher boards, this push block design distributes even and accurate pressure to both sides of the stock for fluid rip cuts. This push block grips both side of the stock and guides it through the table saw cut while safely keeping your fingers and hands out of the way. Eliminates those dangerous close calls with your fingers by the saw blade on narrow rip cuts!
• USER FRIENDLY ADJUSTMENTS TO SET UP EACH RIP CUT- Adjustable center leg is easily adjusted by rolling a wheel with your thumb to set up different width cuts. Innovative balance wheel is deployed via a button to deliver stability on narrow cuts. No annoying thumbscrews that have to be loosened and tightened for each cut.
• COMES FULLY ASSEMBLED, NO INSTALLATION NECESSARY- Arrives ready to go right out of the box, no frustrating assembly required. Other push blocks require IKEA style installation with tons of moving pieces
• LIFETIME WARRANTY- Delmar Tools includes a lifetime warranty on this pushblock. Any issues down the line and you will be covered for a free replacement or a refund.

Delmar Tools